mandatory
mandatory

Recent Posts

Pages: [1] 2 3 ... 10
1
SAM4S Printers / SAM4S OPOS driver
« Last post by Lindsay McPhee on June 24, 2020, 09:35:47 AM »
Hi All,

Please find the OPOS driver attached. 

NB:  This installer requires DotNetFx3 to be installed prior to installing this driver.
2
SPS2000 / SPS2000 PC Utility V3.1.7
« Last post by Lindsay McPhee on January 16, 2020, 10:37:09 AM »
Hi All,

Please attached zip file which contains SPS2000 PC Utility v 3.1.7
3
SAM4S Printers / SAM4S Gcube Windows Driver v3.0.1.9
« Last post by Lindsay McPhee on November 12, 2019, 11:06:41 AM »
Hi All,

Please see driver attached.
4
SAM4S Printers / Re: SAM 4s GIANT 100D format code
« Last post by Lindsay McPhee on August 21, 2019, 02:55:26 PM »
Hi Peter,

Please see attached documentation. 

Don't be concerned about the title only mentioning the Ellix printer.  The same command codes apply to the Giant also.
5
SAM4S Printers / SAM 4s GIANT 100D format code
« Last post by Peter Maddox on August 21, 2019, 12:05:43 PM »
Hello,  can you give me the printer control codes for this model?

I need at least the codes for left and centre justification and Double height print

Thanks,

Peter
6
Ask a Question / Re: Sam4s ER-430m
« Last post by Lindsay McPhee on January 16, 2019, 09:23:30 AM »
Hi Lee,

Please check your cash register's serial port configuration:

Turn Key to Service mode
     needs key with letter 'C' embossed into it
     Service mode is down at 6 O'clock past P Mode

By Default, port 1 is setup for PC comms - but it may have been changed.

To Set port 1 to work with the computer - make sure the Key is in S Mode.
Type :
[
    8 0 Subtotal
    1 X/Time 0 Cash
    2 X/Time 0 Cash
    3 X/Time 0 Cash
    4 X/Time 0 Cash
    5 X/Time 1 Cash  Cash
 ]

Plug your cable into serial port 1 of the cash register and try again.
The key can be in any mode, but you must not have an active transaction running, or you will get a Register not Ready error again.

If your register does NOT go into online mode after doing the above steps, you may have a cable that is internally not wired correctly.

If your register goes into online mode, but you still get a register not ready after doing the above steps, you may have a broken wire inside your cable.
7
Ask a Question / Sam4s ER-430m
« Last post by Lee Beasley on January 15, 2019, 08:57:59 PM »
Hi i have a ER-430M im trying to connect it to my windows 10 PC Via Serial 1 or 2 and have downloaded the Software VIA the Fourms here and followed the instructions but i get stuck after the software opens as when i click "UpProgram ECR ->PC and select All Program as in the instructions i get a error message "REGISTER NOT READY" ive tried Serial 1 and 2 all programed the same as in the instructions but im at a loss Please Help
8
General / Espresso PC Utility for Various Models
« Last post by Lindsay McPhee on December 21, 2017, 01:44:24 PM »
Hi All,

Please find Espresso software Version 2.0.1 and the user manual attached.
9
Printer Software / Ellix Configuration Utility - EllixSet v1.3.11
« Last post by Lindsay McPhee on November 17, 2017, 12:56:27 PM »
Hi All,

Please find the utility attached below.
10
Printer Software / Ellix/Giant printer driver software v 1.9.7
« Last post by Lindsay McPhee on November 17, 2017, 12:41:31 PM »
Hi All,

Please find printer driver version 1.9.7 attached.
Pages: [1] 2 3 ... 10
anything