mandatory
mandatory

Recent Posts

Pages: [1] 2 3 ... 10
1
Ask a Question / Re: Sam4s ER-430m
« Last post by Lindsay McPhee on January 16, 2019, 09:23:30 AM »
Hi Lee,

Please check your cash register's serial port configuration:

Turn Key to Service mode
     needs key with letter 'C' embossed into it
     Service mode is down at 6 O'clock past P Mode

By Default, port 1 is setup for PC comms - but it may have been changed.

To Set port 1 to work with the computer - make sure the Key is in S Mode.
Type :
[
    8 0 Subtotal
    1 X/Time 0 Cash
    2 X/Time 0 Cash
    3 X/Time 0 Cash
    4 X/Time 0 Cash
    5 X/Time 1 Cash  Cash
 ]

Plug your cable into serial port 1 of the cash register and try again.
The key can be in any mode, but you must not have an active transaction running, or you will get a Register not Ready error again.

If your register does NOT go into online mode after doing the above steps, you may have a cable that is internally not wired correctly.

If your register goes into online mode, but you still get a register not ready after doing the above steps, you may have a broken wire inside your cable.
2
Ask a Question / Sam4s ER-430m
« Last post by Lee Beasley on January 15, 2019, 08:57:59 PM »
Hi i have a ER-430M im trying to connect it to my windows 10 PC Via Serial 1 or 2 and have downloaded the Software VIA the Fourms here and followed the instructions but i get stuck after the software opens as when i click "UpProgram ECR ->PC and select All Program as in the instructions i get a error message "REGISTER NOT READY" ive tried Serial 1 and 2 all programed the same as in the instructions but im at a loss Please Help
3
General / Espresso PC Utility for Various Models
« Last post by Lindsay McPhee on December 21, 2017, 01:44:24 PM »
Hi All,

Please find Espresso software Version 2.0.1 and the user manual attached.
4
Printer Software / Ellix Configuration Utility - EllixSet v1.3.11
« Last post by Lindsay McPhee on November 17, 2017, 12:56:27 PM »
Hi All,

Please find the utility attached below.
5
Printer Software / Ellix/Giant printer driver software v 1.9.7
« Last post by Lindsay McPhee on November 17, 2017, 12:41:31 PM »
Hi All,

Please find printer driver version 1.9.7 attached.
6
Printer Software / SAM4S Giant 100 Configuration Utility software
« Last post by Lindsay McPhee on March 03, 2017, 11:01:29 AM »
Hi All,

Please find the Giant Tool Version 2.07 attached.  This can be used to configure the Ethernet interfaces.
7
Printer Software / SAM4S Giant Printer Driver Version 1.9.9a
« Last post by Lindsay McPhee on November 16, 2016, 10:16:26 AM »
Hi All,

Please find the driver attached.
8
Sps300 Series (320, 325, 340,345) / SPS3x0 Firmware version 01.022
« Last post by Lindsay McPhee on August 04, 2016, 01:23:55 PM »
Hi All,

Please find the latest and greatest (at time of writing) firmware attached below.
9
Scale Software / CAS LP1 LP-Works utility
« Last post by Lindsay McPhee on June 15, 2016, 03:48:29 PM »
Hi All,

Please find LP works Utility attached.
10
SPS300 Series (320, 325, 340,345) / Re: Spare Parts
« Last post by Lindsay McPhee on June 14, 2016, 12:11:22 PM »
Hi Vince,

I'll email the manual to you.  I don't have an appropriate board to post service manuals on the forum that is restricted from access by the general public.
Pages: [1] 2 3 ... 10
anything